Netonix Forums

FIXED/CHANGED
- Production requirements for testing forced this release
- This version had to be pushed as a new production run has a new temp sensor as old was discontinued
- fixed issue with watchdog poe bounce that was not completely shutting off power depending on the delay time and offset's used
- fixed memory leak in NET-SNMP

ENHANCEMENTS
- Modified Port Bounce option to read 'Port Bounce POE' and added 'Port Bounce Link' manual option for status and ports tab
- Option in discovery configuration now exists to disable the switch from broadcasting on discovery protocols while the discovery tab is enabled
- link bounce option exists for the watchdog as well as the POE bounce option.

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Eric Stern to help

Released 8/19/2019

FIXED/CHANGED
- WS-12-400-AC would not display port 5 and port 6 monitored power correctly for VH (This bug has been present since before 1.4.9)
- Added Firmware Version to page footer
- DCDC Bootloader Version and DCDC Board Rev display correctly if i2c link to Power Supply is broken on boot up
- vtss_appl is now SIGNIFICANTLY more stable than it was. This was probably the root of many other issue's experienced by users.
- SFP module interaction has improved SIGNIFICANTLY, rebooting, and general operation should no longer cause failure's. It's possible more module's are compatible as well (this requires further testing)
- Boot up now performs a gratuitous ARP broadcast, which prevents the scenario where upon a warm or cold boot (aka firmware upgrade, etc) where loss of connectivity
to the switch's management site or ssh access occurs even if sometimes otherwise the switch is operating.
- Fixed issue, upon boot or config changes, PoE wattage values would disappear on smart DC switches if i2c to the Power Supply failed.
- vtss_appl should no longer crash when Management VLAN ID is changed from default or if IP addresses are assigned to any other VLANs, and overall stability has been increased beyond rc2
- IPv6 address's will no longer be assigned to interfaces via SLAAC when IPv6 is disabled which caused a security concern, instead it is now a configurable option
- fixed vtss_appl crash loop caused by having >8 IP address's assigned to a VLAN

ENHANCEMENTS
- "Stats" checkbox in ports tab when disabled now removes excessive logging for the associated port
- IPv6 "SLAAC" is a separate option in the Device Config Tab under IPv6 as well as the CLI
- New command in CLI "web_conf_check" which will detect and repair web config corruption that can prevent access to the web UI.
- At bootup, switch runs web config check to prevent faulty web UI config

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Eric Stern to help

Released 10/15/2019

FIXED/CHANGED
- Update for new fan's required by manufacturer.
- NTP client refresh's it's connection at a regular interval
- added tooltip to "broadcast on protocols" discovery button
- CLI now shows DC values for WS-8-150-DC for command 'show status'

ENHANCEMENTS
- Latitude and Longitude sent with email from watchdog

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Eric Stern to help

Released 9/16/2020

FIXED/CHANGED
- Enabling/Disabling ports on MSTP could result in loss of connectivity
- updating VLANs port types was not registered with MSTP

ENHANCEMENTS

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Stephen Copeland to help

Released 3/30/2021

FIXED/CHANGED
- calibration systems and current measurement systems completely rebuilt from scratch to fix measurement issue's after OCP fix (related post)
- reworked boot system to fix occasional reported unpredictable behavior at startup.
- fixed PoE changes on any port would briefly turn off PoE on all active ports
- In RC2, switch had difficulty accessing powered radios
- changing hostname in CLI or webGUI caused random behavior
- Management VLANs with tagged ports can now pass traffic
- updates to software to accommodate new hardware updates to improve OCP functionality
*** IMPORTANT NOTE*** This applies specifically for WS3's rev D and greater see this post
- selectable SFP+ speeds updated to include 1G
- Wattage/PoE popup balloons updating correctly for monitoring
- External Sensor monitoring error when removed from switch

ENHANCEMENTS
- "calibrate-ports" command added to CLI, should not typically be needed as devices are calibrated at factory, but should corruption occur, user can run this command to increase port sensor measurement accuracy, most effective on rev D and above.

WARNING do NOT run this command if cables are plugged into ANY non-SFP ports. Also be sure that POE is NOT active on any port, otherwise calibration will NOT occur for that port.

- "show portcals" command added to CLI, display calibration values for port sensors obtained from calibration routine above or values determined at factory.

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Stephen Copeland to help

Released 9/3/2021

FIXED/CHANGED
- Connection with netonix manager works with manager version 1.0.18 or greater

ENHANCEMENTS

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Stephen Copeland to help

Released 10/1/2021

FIXED/CHANGED
- Enabling/Disabling ports on MSTP could result in loss of connectivity
- updating VLANs port types was not registered with MSTP
- Dropbear works again

ENHANCEMENTS

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Stephen Copeland to help

Released 4/3/2021