Setting up PRTG to use SNMP with Netonix

DOWNLOAD THE LATEST FIRMWARE HERE
User avatar
sirhc
Employee
Employee
 
Posts: 7347
Joined: Tue Apr 08, 2014 3:48 pm
Location: Lancaster, PA
Has thanked: 1597 times
Been thanked: 1317 times

Setting up PRTG to use SNMP with Netonix

Mon Nov 30, 2015 6:12 pm

We will assume you already have PRTG installed and running.
These instructions were tested with v1.3.9rc4 or newer firmware.
With v1.3.9 we changed from mini-snmpd to net-snmp, a more common and well tested snmp daemon.


If you have not already also download and install the MIB importer tool (https://www.paessler.com/tools/mibimporter)

To monitor Netonix specific things we need to import the Netonix MIB
- open the MIB importer tool
- click on File > Import MIB File ...
- select the "NETONIX-SWITCH-MIB.dat" file (http://forum.netonix.com/firmware/NETON ... CH-MIB.dat)
- click "Close" on the import log window
- click on File > Save Complete OIDLib
- change the directory to C:\Program Files (x86)\PRTG Network Monitor\snmplibs
- enter the File name as "Netonix.oidlib" and click Save

To monitor the PoE status of ports we need to import the SNMP Power MIB
- open the MIB importer tool
- click on File > Import MIB File ...
- select the "POWER-ETHERNET-MIB.txt" file (https://raw.githubusercontent.com/libre ... HERNET-MIB)
- click "Close" on the import log window
- click on File > Save Complete OIDLib
- change the directory to C:\Program Files (x86)\PRTG Network Monitor\snmplibs
- enter the File name as "Power.oidlib" and click Save
- open the PRTG Network Monitor
- click on "Devices" in the top menu
- click on "Add Device"
- select a group to add the device to and click "Continue >"
- change the "Device Name"
- enter the "IPv4 Address/DNS Name"
- select "Automatic device identification (standard, recommended)"
- click "Continue >"
- wait until Auto-Discovery is complete
- click on the Device Name

Auto-Discovery will only add ports that are currently in use. To add the other ports
- click on "Add Sensor"
- click on "SNMP Traffic"
- click the check box next to any ports that do not have a Status of "Connected"
- click "Continue >"

To monitor Netonix specific things like fan speeds, temperatures and voltages
- click on "Add Sensor"
- click on "SNMP Library"
- select "Netonix.oidlib" from the list and click OK
- click the checkbox just under "Library-OIDs" to select all of the sensors
- click "Continue >"

To monitor the PoE status of ports
- click on "Add Sensor"
- click on "SNMP Library"
- select "Power.oidlib" from the list and click OK
- click the checkbox just under "Library-OIDs" to select all of the sensors
- click "Continue >"
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.

User avatar
bearm
Member
 
Posts: 13
Joined: Thu Dec 24, 2015 5:21 pm
Location: Mechanicsburg, PA
Has thanked: 11 times
Been thanked: 1 time

Re: Setting up PRTG to use SNMP with Netonix

Fri Sep 30, 2016 8:26 am

While the power-ethernet MIB provides access to "per port" consumption in watts, it doesn't appear that the aggregate is directly pollable.
Is that true?

I generally see 11 to 12 watt consumption per the Total item (0W to 400W) in the webui on my WS-24-400A.
(Total consumption is low right now because I have not yet migrated radios to from a TS-8-PRO.)

It would be beneficial to have an aggregate wattage value exported via SNMP to see the overall WISP Switch power supply load.

Thanks,
Mike

User avatar
sirhc
Employee
Employee
 
Posts: 7347
Joined: Tue Apr 08, 2014 3:48 pm
Location: Lancaster, PA
Has thanked: 1597 times
Been thanked: 1317 times

Re: Setting up PRTG to use SNMP with Netonix

Fri Sep 30, 2016 8:59 am

bearm wrote:While the power-ethernet MIB provides access to "per port" consumption in watts, it doesn't appear that the aggregate is directly pollable.
Is that true?

I generally see 11 to 12 watt consumption per the Total item (0W to 400W) in the webui on my WS-24-400A.
(Total consumption is low right now because I have not yet migrated radios to from a TS-8-PRO.)

It would be beneficial to have an aggregate wattage value exported via SNMP to see the overall WISP Switch power supply load.

Thanks,
Mike


Are your running our latest firmware v1.4.5rc2 and using our MIB file?

Eric will comment when he comes on line.
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.

User avatar
Eric Stern
Employee
Employee
 
Posts: 532
Joined: Wed Apr 09, 2014 9:41 pm
Location: Toronto, Ontario
Has thanked: 0 time
Been thanked: 130 times

Re: Setting up PRTG to use SNMP with Netonix

Fri Sep 30, 2016 9:34 am

bearm wrote:While the power-ethernet MIB provides access to "per port" consumption in watts, it doesn't appear that the aggregate is directly pollable.
Is that true?

I generally see 11 to 12 watt consumption per the Total item (0W to 400W) in the webui on my WS-24-400A.
(Total consumption is low right now because I have not yet migrated radios to from a TS-8-PRO.)

It would be beneficial to have an aggregate wattage value exported via SNMP to see the overall WISP Switch power supply load.

Thanks,
Mike


Search the forum for "total power".

viewtopic.php?f=6&t=2156&p=15469&hilit=total+power#p15469

User avatar
bearm
Member
 
Posts: 13
Joined: Thu Dec 24, 2015 5:21 pm
Location: Mechanicsburg, PA
Has thanked: 11 times
Been thanked: 1 time

Re: Setting up PRTG to use SNMP with Netonix

Fri Sep 30, 2016 1:57 pm

Eric Stern wrote:Search the forum for "total power".

http://forum.netonix.com/viewtopic.php? ... wer#p15469


Chris and Eric,

Thanks for the point in the right direction.
I found the changelog for 1.4.5rc2 after commenting on this post (and decided the bug fixes were worth the upgrade). :roll:
I noticed ifAlias now works (basically swapped with ifDescr now) so I can update my graphs to reflect that change. :thumbsup:

Perfect -- take totalpower value and divide by 10.
It appeared I needed to get a copy of the newest MIB too since the human readable name wasn't complete. I have a copy of the latest MIB and it's still not translated to something entirely human readable. :eek: I have the OID I was hoping for (thanks!).

Same thing goes for the last 3 items when I walk just the Netonix Switch MIB
Code: Select all
NETONIX-SWITCH-MIB::netonixSwitch.6.0 = INTEGER: 150
NETONIX-SWITCH-MIB::netonixSwitch.7.0 = INTEGER: 0
NETONIX-SWITCH-MIB::netonixSwitch.8 = INTEGER: 0

User avatar
cwachs
Experienced Member
 
Posts: 115
Joined: Fri Nov 06, 2015 9:04 pm
Location: Colorado
Has thanked: 2 times
Been thanked: 10 times

Re: Setting up PRTG to use SNMP with Netonix

Thu Jul 27, 2017 12:42 pm

How about a MIB to track the total traffic across a LAG and not individual ports of that LAG?

User avatar
Magician
Associate
Associate
 
Posts: 52
Joined: Wed Jul 09, 2014 10:47 am
Has thanked: 7 times
Been thanked: 31 times

Re: Setting up PRTG to use SNMP with Netonix

Mon Nov 27, 2017 1:58 pm

I was trying to get input voltage to track how the solar site is doing. I can't seem to find the value has anyone done this... I see input current not input voltage

User avatar
sirhc
Employee
Employee
 
Posts: 7347
Joined: Tue Apr 08, 2014 3:48 pm
Location: Lancaster, PA
Has thanked: 1597 times
Been thanked: 1317 times

Re: Setting up PRTG to use SNMP with Netonix

Mon Nov 27, 2017 2:15 pm

Magician wrote:I was trying to get input voltage to track how the solar site is doing. I can't seem to find the value has anyone done this... I see input current not input voltage


What model switch are we talking about and what version of firmware are you running on the switch? (I hope v1.4.8)
Are you using our MIB: viewtopic.php?f=17&t=251#p935
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.

User avatar
Magician
Associate
Associate
 
Posts: 52
Joined: Wed Jul 09, 2014 10:47 am
Has thanked: 7 times
Been thanked: 31 times

Re: Setting up PRTG to use SNMP with Netonix

Mon Nov 27, 2017 9:02 pm

sirhc wrote:
Magician wrote:I was trying to get input voltage to track how the solar site is doing. I can't seem to find the value has anyone done this... I see input current not input voltage


What model switch are we talking about and what version of firmware are you running on the switch? (I hope v1.4.8)
Are you using our MIB: viewtopic.php?f=17&t=251#p935


Switch is WS-12-250-DC
Firmware 1.4.8
and yes the referenced mib


in PRTG for "netonix switch/dcdc" input current I would expect the .4A the gui reports... We actually prtg reports 3.2 - 5.0 as a % but no field of input voltage which is the number I need.

User avatar
Eric Stern
Employee
Employee
 
Posts: 532
Joined: Wed Apr 09, 2014 9:41 pm
Location: Toronto, Ontario
Has thanked: 0 time
Been thanked: 130 times

Re: Setting up PRTG to use SNMP with Netonix

Tue Nov 28, 2017 11:38 am

The OID for input voltage on WS-12-250-DC is 1.3.6.1.4.1.46242.4.1.3.4

Next
Return to Hardware and software issues

Who is online

Users browsing this forum: No registered users and 17 guests