v1.5.1rcX Bug Reports and Comments

DOWNLOAD THE LATEST FIRMWARE HERE
User avatar
Stephen
Employee
Employee
 
Posts: 965
Joined: Sun Dec 24, 2017 8:56 pm
Has thanked: 77 times
Been thanked: 169 times

Re: v1.5.1rcX Bug Reports and Comments

Tue Jul 24, 2018 4:46 pm

VLAN Trunking on our switch is to allow the switch to accept tagged packets from VLANs other than ones explicitly configured on the VLAN page. Therefore including a VLAN on the trunk list whether it's defined or not by definition means that it won't be excluded. On that note, if you want to exclude a VLAN defined on the page, simply remove it from the trunk list and you can set the relevant port to 'E'.

slowe
Member
 
Posts: 29
Joined: Sun May 01, 2016 9:47 pm
Has thanked: 1 time
Been thanked: 4 times

Re: v1.5.1rcX Bug Reports and Comments

Wed Jul 25, 2018 11:04 am

In the past when we have been changing a VLAN to E and it’s in the trunk list was it still actually passing that vlan traffic on that port that had the E?

User avatar
Stephen
Employee
Employee
 
Posts: 965
Joined: Sun Dec 24, 2017 8:56 pm
Has thanked: 77 times
Been thanked: 169 times

Re: v1.5.1rcX Bug Reports and Comments

Wed Jul 25, 2018 2:57 pm

Would you happen to know which version of code you are referring too? I can double check for you if you can tell me which one was doing this.

User avatar
sirhc
Employee
Employee
 
Posts: 7347
Joined: Tue Apr 08, 2014 3:48 pm
Location: Lancaster, PA
Has thanked: 1597 times
Been thanked: 1317 times

v1.5.1rc3 Released

Thu Aug 02, 2018 2:36 pm

v1.5.1rcX wrote:FIXED/CHANGED
- Fixed voltage input calibration for the WS-8-150-DC - RC1
- Fixed services running on IPv6 - RC2
- Fixed being able to bypass console login by hitting CTRL-C - RC2
- Fixed MSTP setting instance forwarding state - RC2
-
Fixed UI on ERPS tab to prevent footer from from being mangled - RC3
- Fixed ERPS MEPs issue that triggered a Signal Fail on a ring when port not in the ring is disconnected/disabled - RC3
- Fixed ERPS issue that prevented access to Management VLAN when added to the protected VLAN list - RC3
- Fixed ERPS protected VLANs would not forward packets outside of the ring - RC3

ENHANCEMENTS

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Eric Stern to help
- IGMP snooping over VLANS, MSTP, and ERPS are still being developed

RC1 Released 6/20/2018
RC2 Released 7/10/2018
RC3 Released 8/2/2018
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.

surfermarty
Member
 
Posts: 6
Joined: Thu Apr 28, 2016 3:24 am
Has thanked: 0 time
Been thanked: 0 time

Re: v1.5.1rcX Bug Reports and Comments

Thu Aug 09, 2018 11:02 am

1.5.1rc3

Received a new WS-12-250-DC recently that requires FW > 1.5 according to the sheet of paper that accompanied it. We've put on 1.5.1rc3 and now find no response to any SNMP queries on either v1 or v2c. Internal network so no firewalls involved; nothing configured (intentionally) on the Netonix with regards to management restrictions. IP working fine - we can probe it remotely from across the network.

Anything I can try to see if we can get SNMP working again, or anything I need to provide to help debug it?

Thanks.

Marty

surfermarty
Member
 
Posts: 6
Joined: Thu Apr 28, 2016 3:24 am
Has thanked: 0 time
Been thanked: 0 time

Re: v1.5.1rcX Bug Reports and Comments

Thu Aug 09, 2018 11:09 am

Ok, so after engaging my brain and remembering this is really unix under the hood - the daemon isn't running and when you try to run it by hand, it seg-faults

admin@NTX:/tmp/log# /usr/sbin/snmpd -Le -p /var/run/snmpd.conf -f
Cannot find module (IP-MIB): At line 0 in (none)
Cannot find module (IF-MIB): At line 0 in (none)
Cannot find module (TCP-MIB): At line 0 in (none)
Cannot find module (UDP-MIB): At line 0 in (none)
Cannot find module (HOST-RESOURCES-MIB): At line 0 in (none)
Cannot find module (SNMPv2-MIB): At line 0 in (none)
Cannot find module (SNMPv2-SMI): At line 0 in (none)
Cannot find module (NOTIFICATION-LOG-MIB): At line 0 in (none)
Cannot find module (SNMP-VIEW-BASED-ACM-MIB): At line 0 in (none)
Cannot find module (SNMP-COMMUNITY-MIB): At line 0 in (none)
Cannot find module (SNMP-FRAMEWORK-MIB): At line 0 in (none)
Cannot find module (SNMP-MPD-MIB): At line 0 in (none)
Cannot find module (SNMP-USER-BASED-SM-MIB): At line 0 in (none)
Cannot find module (TUNNEL-MIB): At line 0 in (none)
Cannot find module (UCD-DLMOD-MIB): At line 0 in (none)
Cannot find module (IPV6-ICMP-MIB): At line 0 in (none)
Cannot find module (IPV6-MIB): At line 0 in (none)
Cannot find module (IPV6-TCP-MIB): At line 0 in (none)
Cannot find module (IPV6-UDP-MIB): At line 0 in (none)
Segmentation fault

Known issue?

User avatar
Stephen
Employee
Employee
 
Posts: 965
Joined: Sun Dec 24, 2017 8:56 pm
Has thanked: 77 times
Been thanked: 169 times

Re: v1.5.1rcX Bug Reports and Comments

Thu Aug 09, 2018 2:40 pm

Just to check the basics have you enabled snmp in your device configuration tab?

User avatar
dray
Member
 
Posts: 18
Joined: Sun Oct 04, 2015 12:11 pm
Location: Las Vegas, NV
Has thanked: 0 time
Been thanked: 2 times

Re: v1.5.1rcX Bug Reports and Comments

Thu Aug 09, 2018 3:09 pm

SNMP broke for me on a WS-12-250-DC. Trying different versions and settings, and rebooting didnt help.

v1.5.1.rc3

User avatar
Stephen
Employee
Employee
 
Posts: 965
Joined: Sun Dec 24, 2017 8:56 pm
Has thanked: 77 times
Been thanked: 169 times

Re: v1.5.1rcX Bug Reports and Comments

Thu Aug 09, 2018 8:04 pm

OK it does appear there is a problem here.
Stay tuned, working on a new update.

surfermarty
Member
 
Posts: 6
Joined: Thu Apr 28, 2016 3:24 am
Has thanked: 0 time
Been thanked: 0 time

Re: v1.5.1rcX Bug Reports and Comments

Fri Aug 10, 2018 6:25 am

Yes - SNMP is enabled - tried both V1, V2c and then both - the fact the daemon isn't running and is seg faulting would seem to be the issue.

PreviousNext
Return to Hardware and software issues

Who is online

Users browsing this forum: No registered users and 11 guests